Beck's CRS Blog http://www.beckscrs.com/blog Wed, 09 Jun 2010 01:28:29 +0000 http://wordpress.org/?v=2.1.2 en Canon Pixma MP830 firmwear upgrade http://www.beckscrs.com/blog/index.php/pixma-mp830-firmwear-upgrade/ http://www.beckscrs.com/blog/index.php/pixma-mp830-firmwear-upgrade/#comments Fri, 23 Mar 2007 12:39:08 +0000 admin http://www.beckscrs.com/blog/index.php/pixma-mp830-firmwear-upgrade/

PRODUCT(S): PIXMA MP830

AFFECTED: All Units

DESCRIPTION: Mandatory Main ROM Upgrade

SOLUTION(S): Upgrade the EEPROM on the Main Board to Version 1.13

See a Canon Authorized service center and have it done, its a flash to your ROM chip.

]]> http://www.beckscrs.com/blog/index.php/pixma-mp830-firmwear-upgrade/feed/ 5 Alternating Blinks (SFP) / ##356 (MFP) - ASF Cam Sensor Error http://www.beckscrs.com/blog/index.php/5-alternating-blinks-sfp-356-mfp-asf-cam-sensor-error/ http://www.beckscrs.com/blog/index.php/5-alternating-blinks-sfp-356-mfp-asf-cam-sensor-error/#comments Fri, 23 Mar 2007 05:13:57 +0000 admin http://www.beckscrs.com/blog/5-alternating-blinks-sfp-356-mfp-asf-cam-sensor-error/ SFP: PIXMA iP3000/4000/4000R/5000/6000D/8500

MFP: PIXMA MP750/760/780

DESCRIPTION: 5 Alternating Blinks (SFP) / ##356 (MFP) - ASF Cam Sensor Error

SOLUTION(S): Adjust the Screws & Main Case Unit

Movement (i.e. from shipping) may cause the plastic guide to move away from the chassis. When this

occurs, the gears cannot rotate properly causing a grinding noise and 5 alternating blinks (SFP) or ##356

(MFP) - ASF Cam Sensor Error.

]]> http://www.beckscrs.com/blog/index.php/5-alternating-blinks-sfp-356-mfp-asf-cam-sensor-error/feed/ My MP 700/MP730: Blank Pages are Fed Through the Auto Sheet Feeder Before and After the Printed http://www.beckscrs.com/blog/index.php/my-mp-700mp730-blank-pages-are-fed-through-the-auto-sheet-feeder-before-and-after-the-printed/ http://www.beckscrs.com/blog/index.php/my-mp-700mp730-blank-pages-are-fed-through-the-auto-sheet-feeder-before-and-after-the-printed/#comments Fri, 23 Mar 2007 05:13:11 +0000 admin http://www.beckscrs.com/blog/my-mp-700mp730-blank-pages-are-fed-through-the-auto-sheet-feeder-before-and-after-the-printed/ SOLUTION(S): Reset the Sheet Feeder Gears

If the power fails while the paper is feeding or during a print job, the paper feed gears will lose their proper

alignment. The reason is that after the power is restored the paper feed gears will attempt to return to the

home position, which may not be possible if the paper stop cam is not in the correct position.

]]> http://www.beckscrs.com/blog/index.php/my-mp-700mp730-blank-pages-are-fed-through-the-auto-sheet-feeder-before-and-after-the-printed/feed/